• Thanks for visiting The Penturners Forum today.

    There are many features and resources that currently you are unable to see or access, either because you're not yet registered, or if you're already registered, because you're not logged in.

    To gain full access to the forum, please log in or register now. Registration is completely free, it only takes a few seconds, and you can join our well established community of like-minded pen makers.

New to this, how do I ??

evoman76

Apprentice Member
Joined
Jul 14, 2017
Posts
9
Location
Maidstone, Kent
First Name
David
Hi

I have been making pens for a while now and would like to experiment with making my own blanks. I work in the cardboard packaging industry and wondered if it would be possible to make a blank with cardboard in so you can see the flute(wiggly bit in the middle) Would the resin go around / through this to make it strong enough ?

If so where do I get moulds and clear resin ?

Thanks in advance

David
 

Phil Dart

Moderator
Executive Member
Joined
Nov 28, 2014
Posts
5,455
Location
Colebrooke, Devon
First Name
Phil
Hi David - Welcome to the Forum

There are lots of blanks makers and casters here, and doubtless some will be along to help you before long.
 

fingwe

Registered
Joined
Nov 2, 2015
Posts
322
Location
Suffolk
First Name
Melanie
Hmm, I'm not sure, you might be OK if you cast it in a vacuum chamber, or possibly a pressure pot, but otherwise I think the resins are going to be too thick to penetrate the cardboard evenly in the limited curing time. You might have better luck with an epoxy resin, which will generally take around a day to cure, but even then I would expect it to be a bit patchy, without the use of vacuum/pressure - and you'll generate lots of air bubbles. Actually, I think bubbles may end up being your biggest problem....
 

21William

Fellow
Joined
Jan 21, 2016
Posts
1,618
Location
Dorset
First Name
William
Some Epoxy resins have a pretty low viscosity but I think Melanie is right about needing a vacuum chamber. Nice idea though, might turn out nice if you can do it.
 

Bucks

Fellow
Joined
Apr 26, 2016
Posts
1,425
Location
North Yorkshire
First Name
Paul
My brain is so fried at the moment with the Christmas rush, but I’m sure that with a little thought & experimentation there will me a way, you could possibly try sealing the cardboard with some form of spray sealer/lacquer, to prevent the cardboard from just becoming a soggy mess from the resin.

As to suppliers of moulds & Resins, I make quality casting moulds available here www.PenBlanksAndMoulds.co.uk.

You can get various resins from places like Easy Composites, East Coast Fiberglass or MB Fibreglass
 

fingwe

Registered
Joined
Nov 2, 2015
Posts
322
Location
Suffolk
First Name
Melanie
I was thinking about sealing it, but then you may prevent the resin soaking through into the holes in the cardboard, leaving voids. The superglue idea that Peter had might work, but it will cost a lot in superglue, and there may still be the problem of voids in the middle of the cardboard.
 

Phil Dart

Moderator
Executive Member
Joined
Nov 28, 2014
Posts
5,455
Location
Colebrooke, Devon
First Name
Phil
I will give it a go. What colour resin do you want?

Bite Paul's hand off David. My guess is that there'll also be a short video to document the experiment, and success or failure, Paul's videos are always worth watching.

(no pressure Paul):wink:
 

evoman76

Apprentice Member
Joined
Jul 14, 2017
Posts
9
Location
Maidstone, Kent
First Name
David
Hi Paul, thanks for the very kind offer, I was thinking a clear resin would be good to show the full shape / style of the cardboard ?
 

Paul hd

Fellow
Joined
Jun 12, 2016
Posts
1,299
Location
Buckinghamshire
First Name
Paul
(no pressure Paul):wink:
Has to be a little bit of pressure. About 60psi :thumbs:

Hi Paul, thanks for the very kind offer, I was thinking a clear resin would be good to show the full shape / style of the cardboard ?

Hi David,

I will cast one in Clear resin for you.

I did have a go and I made one in Blue which was put in the pressure chamber and one in White which was left to cure without pressure.

My conclusion is that it definitely needs pressure.

It was a good experiment and I really enjoyed doing it. To be continued.......

cardboard - YouTube
 

Phil Dart

Moderator
Executive Member
Joined
Nov 28, 2014
Posts
5,455
Location
Colebrooke, Devon
First Name
Phil
You certainly don't let the grass grow Paul. Quite apart from the casting aspect, it will be interesting to see how they drill and turn, and above all, take to finishing. Not being a caster myself, I'm assuming that the pressure will have caused the cardboard to have absorbed the resin and therefore platicised - is that right??
 

Paul hd

Fellow
Joined
Jun 12, 2016
Posts
1,299
Location
Buckinghamshire
First Name
Paul
it will be interesting to see how they drill and turn, and above all, take to finishing. Not being a caster myself, I'm assuming that the pressure will have caused the cardboard to have absorbed the resin and therefore platicised - is that right??

To be honest Phil I do not know. I am hoping the pressure does push the resin into the cardboard as it only takes 8 minutes for the Alumilite to go off.

Today I will drill, turn and polish and get some answers.

Cheers
Paul
 

Phil Dart

Moderator
Executive Member
Joined
Nov 28, 2014
Posts
5,455
Location
Colebrooke, Devon
First Name
Phil
Brilliant. Well done Paul - your willingness to jump straight in there and experiment does you proud. And the result looked looked great too.
 
Warning! This thread has not had any replies for over a year. You are welcome to post a reply here, but it might be better to start a new thread (and maybe include a link to this one if you need to).
Top