• Thanks for visiting The Penturners Forum today.

    There are many features and resources that currently you are unable to see or access, either because you're not yet registered, or if you're already registered, because you're not logged in.

    To gain full access to the forum, please log in or register now. Registration is completely free, it only takes a few seconds, and you can join our well established community of like-minded pen makers.

What Finish?

Dalboy

Executive Member
Joined
Mar 20, 2014
Posts
7,679
Location
Kent
First Name
Derek
I would use an oil finish just don't put it on to heavy especially in the rough areas. Keep doing this until it no longer soaks in, allow each coat to dry before applying the next and wipe off any excess that is on the piece after 10 minutes this allows it to soak in and prevents heavy build up.
 

21William

Fellow
Joined
Jan 21, 2016
Posts
1,618
Location
Dorset
First Name
William
What finish would you like to use? You could apply any number of finishes with the correct procedure. A stiff brush should easily apply, Oil, Lacquer or even Wax to the rough areas with some care. The biggest problem is likely to be getting too much of whatever you choose on the rough bits.

Next time choose a better bit of wood! :funny:
 

DaveP

Apprentice Member
Joined
Nov 28, 2018
Posts
20
Location
Dumfries and Galloway
First Name
David
I would recommend.... a metal powder (whatever takes your fancy, brass / aluminum mixed with epoxy or resin and run into the imperfections) then after sanding the worlds your oyster, but I'd just go for shellac, cos I'm feeling lazy

Or maybe forget the metal powder and just use resin .... maybe
 

wm460

Grand Master
Joined
Mar 16, 2013
Posts
23,095
Location
Tennant Creek, Northern Territory, Australia.
First Name
Mark
I would use an oil finish just don't put it on to heavy especially in the rough areas. Keep doing this until it no longer soaks in, allow each coat to dry before applying the next and wipe off any excess that is on the piece after 10 minutes this allows it to soak in and prevents heavy build up.

What type of oil do you recommend Derek?


What finish would you like to use? You could apply any number of finishes with the correct procedure. A stiff brush should easily apply, Oil, Lacquer or even Wax to the rough areas with some care. The biggest problem is likely to be getting too much of whatever you choose on the rough bits.

Normally I would use wax after finishing a previous bowl with wax a couple day earlier, no way.:sob:

Next time choose a better bit of wood! :funny:

I manage to steal 1/2 dozen pieces of firewood from a freezing cold pensioner down south last time I was there.
I had to be quick to avoid his savage dogs.:goesred:

I'd be using oil if it were mine too.
What type?
Hopefully available in Aust.:praying:

I dont want to fill it with resin, leave it as it is as a feature.
 

Dalboy

Executive Member
Joined
Mar 20, 2014
Posts
7,679
Location
Kent
First Name
Derek
I would say Danish Oil but I know that you did not have a great success with it. Contact your supplier of finishes down there to see what oils they have you may need to send them an e mail as i can only see one oil on their page
 

Phil Dart

Moderator
Executive Member
Joined
Nov 28, 2014
Posts
5,455
Location
Colebrooke, Devon
First Name
Phil
What type?
Hopefully available in Aust.:praying:

I'm not sure that danish oil would be best on that piece anyway. (Sorry Derek) It needs buffing to get the best results, and unless you get into every crack, fissure and pore with a brush, you just end up with a build up of yellow, manky horribleness.

Tung oil is a bit better - dilute the first couple of coats 50/50 with white spirit. You still need to be quite diligent about removing the excess from the spaces though.

For me, I would nearly always go for the highly under-rated and almost totally ignored supermarket vegetable oil on a piece like that. Brush it on and leave it for 5 minutes, then wipe it off. Leave it overnight and repeat several times. It will build up a nice sheen and either adsorbs or runs out of the cracks and pores. Nut oils will do the same job but you'll pay more for them, but don't be tempted to use sunflower or olive oil, as both will go rancid.

And if you can't get it in Aus, you need to move.:thinks:
 

21William

Fellow
Joined
Jan 21, 2016
Posts
1,618
Location
Dorset
First Name
William
Danish is one of my least favourite oils, as said it can end up as a horrible sticky mess if you’re not careful. Easy enough to clean off a flat smooth surface but on the rough voids in that bowl? I wouldn’t risk it. True Oil or something similar may be a better bet.
 
Warning! This thread has not had any replies for over a year. You are welcome to post a reply here, but it might be better to start a new thread (and maybe include a link to this one if you need to).
Top