• Thanks for visiting The Penturners Forum today.

    There are many features and resources that currently you are unable to see or access, either because you're not yet registered, or if you're already registered, because you're not logged in.

    To gain full access to the forum, please log in or register now. Registration is completely free, it only takes a few seconds, and you can join our well established community of like-minded pen makers.

Garno

Fellow
Joined
May 12, 2021
Posts
1,372
Location
Dronfield
First Name
Gary
Well no doubt you will all be aware of the old saying "Patience is a virtue" (not going to mention "Patience" only has 1 "T" :whistling::whistling: )

Patience is a virtue that would feature very low on a list of traits that I am known for :goesred:

It was only two days ago that I thought the time was getting close that I may need to change lathes, I think it was only yesterday that I actually decided really did need to swap lathes, it was only yesterday that I decided not only to change lathes but to actually upgrade one.

Spent a good few hours yesterday and today raising the money and pulled the trigger on this one today Amazon.co.uk and it is arriving between Sat 13th and Tuesday 16th

Stupid delivery service making me wait for ever for it :vangry::vangry::vangry:

I think I have been patient (2 "t's" :whistling: ) with this purchase and would say I have chosen well. When it eventually gets here :sleeping: I will take lots of photos of it and share them on here (including unpacking) so between now and then you good folk will have to take a leaf from my book and show a bit of patience ( one "t" :whistling: ).
 

flexi

Executive Member
Joined
Sep 12, 2014
Posts
6,160
Location
Maidstone
First Name
mark
Can I just ask, why didn't you go direct to Axi, there next day delivery on most things?? Or wait till black Friday?? Or chat to Axi as sometimes they have good deals on returned items (unboxed but unused)...... Just a thought...
 

Garno

Fellow
Joined
May 12, 2021
Posts
1,372
Location
Dronfield
First Name
Gary
Can I just ask, why didn't you go direct to Axi, there next day delivery on most things?? Or wait till black Friday?? Or chat to Axi as sometimes they have good deals on returned items (unboxed but unused)...... Just a thought...

To raise enough funds I had to send some pen Jaws back (only had them a day :sob: and the money was placed on my amazon account, that tied me into Amazon.
 

alan morrison

Fellow
Joined
Feb 26, 2019
Posts
2,380
Location
Co. Down N Ireland
First Name
Alan
I think that it's the same price anyway, Gary. you just have a longer wait. It's all to teach you more patience.
All the best with your new lathe when it eventually arrives.( mine is similar )
There will be no stopping you now. Take some time and take some photographs.

Alan
 

Garno

Fellow
Joined
May 12, 2021
Posts
1,372
Location
Dronfield
First Name
Gary
I think it will be near summer 2022 before any new chucks, gives me plenty of time to make some pens :whistling:
 

alpha1

Fellow
Joined
Mar 29, 2018
Posts
1,177
Location
middlesbrough
First Name
Dave
Its fine for making pens and small bowls. I have a couple of lathes. I have it set up with a set of pen jaws at the moment. Makes drilling blanks so much easier. I tend to do most of my pen turning on a metal lathe. You will need a decent chuck and some extra jaws etc if you are planning on turning bowls.
I struck lucky I bought it off one of the Guys on here it came with a chuck and some extras and it was about half the price of a new one.
 

silver

General dogsbody
Executive Member
Joined
Jun 29, 2013
Posts
6,301
Location
Somewhere in Staffordshire,
First Name
Eamonn.
Brilliant, well done for getting plenty of funds together. But I thought Amazon had to refund to the card once the item had been returned! :thinks: Have done with anything I had returned. Or was it patience (with one “T” ) that caused that?

I have one of the old girls of this model, brilliant little lathe. (I do have others as well tho :goesred:) I have had it 9 years, brought it off Woody who was on here a lot at one point. Still around but on others streams of social media. Had it for grandson, but now I use it for drilling and finishing blanks. It’s about all she gets used for but a great little lathe.
 

Garno

Fellow
Joined
May 12, 2021
Posts
1,372
Location
Dronfield
First Name
Gary
But I thought Amazon had to refund to the card once the item had been returned! :thinks: Have done with anything I had returned. Or was it patience (with one “T” ) that caused that?

It was indeed lack of patience and even more a lack of thinking on my part :rolling::rolling::goesred::goesred::goesred:
 

silver

General dogsbody
Executive Member
Joined
Jun 29, 2013
Posts
6,301
Location
Somewhere in Staffordshire,
First Name
Eamonn.
It was indeed lack of patience and even more a lack of thinking on my part

You have a team of experienced “thinkers” on here Gary, just ask the question. There is always someone willing to share their buying experience. Oh, I forgot Patience came into play again.:funny:
 

pittswood

Fellow
Joined
Mar 14, 2016
Posts
1,251
Location
Rhigos, South Wales
First Name
Kelvin
I have the same model lathe, fab lathe, good speeds + variable. I use Record sc4 chucks and jaws, never had any problems with them. Used it for bowls, pens even a little metal work on it. Also have a Rockler extractor and face protector on it. its a easy usable lathe, you should enjoy using it. Just don't put the tray behind the tailstock, you will trap your fingers behind it.
Kelvin
 
Warning! This thread has not had any replies for over a year. You are welcome to post a reply here, but it might be better to start a new thread (and maybe include a link to this one if you need to).
Top