• Thanks for visiting The Penturners Forum today.

    There are many features and resources that currently you are unable to see or access, either because you're not yet registered, or if you're already registered, because you're not logged in.

    To gain full access to the forum, please log in or register now. Registration is completely free, it only takes a few seconds, and you can join our well established community of like-minded pen makers.

flexi

Executive Member
Joined
Sep 12, 2014
Posts
6,159
Location
Maidstone
First Name
mark
Hi all, well I have done a few more bullet case pens......
These are .30 06 and fitted with new bullets, drilled to take a slimline refill. These are very long cases so a bit of thought had to go into these to allow the transmission to sit further in, the caps were a lot easier......I still have another 40 odd to do(20 pens) wish me luck!IMG_20190215_182026.jpg
 

angelo49

Registered
Joined
Jun 19, 2013
Posts
2,827
Location
Lancaster, PA Brooklyn, NY USA
First Name
Angelo
Very nice Mark!!:thumbs::thumbs:
I like how the joint lines up perfectly.
Sometimes the drill follows an off center firing pin dent.
I either turn a new center on the metal lathe then drill or drill
from the inside.There is a perfectly centered recess that the drill will follow.
 

flexi

Executive Member
Joined
Sep 12, 2014
Posts
6,159
Location
Maidstone
First Name
mark
Very nice Mark!!:thumbs::thumbs:
I like how the joint lines up perfectly.
Sometimes the drill follows an off center firing pin dent.
I either turn a new center on the metal lathe then drill or drill
from the inside.There is a perfectly centered recess that the drill will follow.

Hi Angelo, thank you....
I have a little trick for centering the drill......I use a reloading press to prep the cases, it resizes the neck and pushes the spent primers out..... they are 5mm so if I use a 6 mm drill first it 'normaly' centers on the primmer pocket:thumbs::thumbs:
 

angelo49

Registered
Joined
Jun 19, 2013
Posts
2,827
Location
Lancaster, PA Brooklyn, NY USA
First Name
Angelo
''I have a little trick for centering the drill......I use a reloading press to prep the cases, it resizes the neck and pushes the spent primers out..... they are 5mm so if I use a 6 mm drill first it 'normaly' centers on the primmer pocket''
Well, that's a good tip!
Thanks
Angelo
 

PetrolP

Full Member
Joined
Jul 12, 2015
Posts
254
Location
Cambridgeshire
First Name
Peter
Amazing, Mark

How long does each one take to make?
They look time consuming but very effective.
Do you finish the brass case with anything ?

Peter
 

Penpal

Grand Master
Joined
May 26, 2013
Posts
25,340
Location
Canberra AUSTRALIA
First Name
Peter
No luck needed Mark you have mastered this with a beaut solution. My solution is to buy ammunition new without primers fitted. That takes care of knecking and stuff ,gives a wonderful case finish.

Immersed as you are these examples prove all the pre time spent was worthwhile and obvious.Wish you good fortune mate.

Peter.
 

flexi

Executive Member
Joined
Sep 12, 2014
Posts
6,159
Location
Maidstone
First Name
mark
Amazing, Mark

How long does each one take to make?
They look time consuming but very effective.
Do you finish the brass case with anything ?

Peter

Hi Peter,
I always batch these....once I have them sized and de primmed, I then seat a bullet and crimp the case, drill out the primmer pocket, glue in the tubes. It's then just push fitting the kit. As to any finish I like the once fired look so a little polish and then a laquer finish.
In total about 1hr per case and about 5 minutes each bullet to drill out if batched
 

flexi

Executive Member
Joined
Sep 12, 2014
Posts
6,159
Location
Maidstone
First Name
mark
Nicely :thumbs::thumbs: done.

How do you remove the lead contamination?:thinks:

Les

Hi Les,
I have seen various methods all with varying degrees of success.....some remove the back of the jacket and warm with a torch till it melts the lead, way too dangerous for me and it discoloures the head.
The method I use works 90% of the time....I drill my 2mm hole from the front first using a collet chuck on the lathe, then reverse the head and drill the back with a 6.5mm after a certain depth when I withdraw, it takes all the lead out with it. I cover the lathe bed when I do this and keep all the swarf and dimples of lead as a friend uses this to recast into ball shot for his muzzle loader:whistling:
 

Les ELm

Executive Member
Joined
Oct 19, 2014
Posts
5,493
Location
Red Deer, Alberta, Canada
First Name
Les
Hi Les,
I have seen various methods all with varying degrees of success.....some remove the back of the jacket and warm with a torch till it melts the lead, way too dangerous for me and it discoloures the head.
The method I use works 90% of the time....I drill my 2mm hole from the front first using a collet chuck on the lathe, then reverse the head and drill the back with a 6.5mm after a certain depth when I withdraw, it takes all the lead out with it. I cover the lathe bed when I do this and keep all the swarf and dimples of lead as a friend uses this to recast into ball shot for his muzzle loader:whistling:

I have done similar to remove lead, but now I use solid brass bullets.

Les
 

Attachments

  • DSC05189.jpg
    DSC05189.jpg
    37.7 KB · Views: 9
  • DSC05249.jpg
    DSC05249.jpg
    24.8 KB · Views: 9
  • krogle-LOS-skupinska-2.jpg
    krogle-LOS-skupinska-2.jpg
    12.5 KB · Views: 9

flexi

Executive Member
Joined
Sep 12, 2014
Posts
6,159
Location
Maidstone
First Name
mark
Hi Les, they look like the 'los' bullets....I have some Barnes 'TSX' heads TBH they are bloody hard to drill....if it was a metal lathe I had with coolent I would go that way, but it's far to messy for my wood lathe and a rabbit hole I don't want to go down.....yet...:whistling:
 

flexi

Executive Member
Joined
Sep 12, 2014
Posts
6,159
Location
Maidstone
First Name
mark
You guys should make a video of the process. It would make good viewing.

My good friend Mik Lawrence recently did a live feed on Facebook to show exactly that. TBH there not that hard when your all set up for it, like everything else.... preparation, preparation,preparation.....
If anyone would like to try these I am happy to pass on cartridges and heads and instructions, buy your own slimline kits though:face:
 

Paul hd

Fellow
Joined
Jun 12, 2016
Posts
1,299
Location
Buckinghamshire
First Name
Paul
My good friend Mik Lawrence recently did a live feed on Facebook to show exactly that. TBH there not that hard when your all set up for it, like everything else.... preparation, preparation,preparation.....
If anyone would like to try these I am happy to pass on cartridges and heads and instructions, buy your own slimline kits though:face:

Hi Mark,
That is very good of you. I have sent you a PM:thumbs:
 
Warning! This thread has not had any replies for over a year. You are welcome to post a reply here, but it might be better to start a new thread (and maybe include a link to this one if you need to).
Top