• Thanks for visiting The Penturners Forum today.

    There are many features and resources that currently you are unable to see or access, either because you're not yet registered, or if you're already registered, because you're not logged in.

    To gain full access to the forum, please log in or register now. Registration is completely free, it only takes a few seconds, and you can join our well established community of like-minded pen makers.

Failed Knife

sammy

Graduate Member
Joined
Dec 13, 2016
Posts
945
Location
Staffordshire
First Name
George
I turned a letter opener but it got spoiled when I sprayed it with melamine lacquer. The pyrography usually separates the colours, but this time the green and yellow mingled quite badly. I'm wondering if it would be better to go down the acrylic route with acrylic sanding sealer and acrylic lacquer instead of my usual cellulose method. Any tips about preventing runs between stains appreciated.
knife.jpg
George
 

Dalboy

Executive Member
Joined
Mar 20, 2014
Posts
7,679
Location
Kent
First Name
Derek
i think we really need to know what you used to colour the handle with as this can effect what finish you use. Some are just not compatible which you have found out. Also how it was applied was it wiped on or sprayed
 

Terry Q

Fellow
Joined
Oct 8, 2014
Posts
3,847
Location
Roanoke, Illinois USA
First Name
Terry

Attachments

  • 2013-06-24 11.16.56_kindlephoto-66864982.jpg
    2013-06-24 11.16.56_kindlephoto-66864982.jpg
    123.8 KB · Views: 62

Phil Dart

Moderator
Executive Member
Joined
Nov 28, 2014
Posts
5,455
Location
Colebrooke, Devon
First Name
Phil
If you're using a spirit based stain, you need to use an acrylic based finish. A water based stain needs a spirit based finish. If you finish spirit with spirit, or water with water, you run the risk of bleeding, as in either like for like case the finish is likely to dissolve the stain to some extent.
 

sammy

Graduate Member
Joined
Dec 13, 2016
Posts
945
Location
Staffordshire
First Name
George
i think we really need to know what you used to colour the handle with as this can effect what finish you use. Some are just not compatible which you have found out. Also how it was applied was it wiped on or sprayed

Thanks Derek, I used Chestnut spirit stains on the bare wood then sprayed chestnut melamine lacquer over the top. I didn't use any sealer. I'm now beginning to think that the problem was in the staining, I put on three coats of the green to get a deep dark colour, perhaps the wood became over saturated and the last coat just sat on the top.
George
 

sammy

Graduate Member
Joined
Dec 13, 2016
Posts
945
Location
Staffordshire
First Name
George

Dalboy

Executive Member
Joined
Mar 20, 2014
Posts
7,679
Location
Kent
First Name
Derek
The reason I asked is already been explained by Phil so will not repeat what he has said
 

sammy

Graduate Member
Joined
Dec 13, 2016
Posts
945
Location
Staffordshire
First Name
George
If you're using a spirit based stain, you need to use an acrylic based finish. A water based stain needs a spirit based finish. If you finish spirit with spirit, or water with water, you run the risk of bleeding, as in either like for like case the finish is likely to dissolve the stain to some extent.

Thanks for that Phil, what you say makes perfect sense now. My mistake is that I thought if you started off with a cellulose product then you followed through with the same. I guess the idea came from my first job 50 odd years ago, when I was told that gloss, oil based paint, shouldn't be used on top of water based emulsion. I will give your suggestion a whirl next time. Thanks again
 
Warning! This thread has not had any replies for over a year. You are welcome to post a reply here, but it might be better to start a new thread (and maybe include a link to this one if you need to).
Top