• Thanks for visiting The Penturners Forum today.

    There are many features and resources that currently you are unable to see or access, either because you're not yet registered, or if you're already registered, because you're not logged in.

    To gain full access to the forum, please log in or register now. Registration is completely free, it only takes a few seconds, and you can join our well established community of like-minded pen makers.

foot switch

cowboy

Registered
Joined
Feb 23, 2014
Posts
445
Location
Huddersfield
Hi all
Where is the best place to buy a foot switch for the scroll saw and what are the best one to get or is some one selling one :praying:
 

Penpal

Grand Master
Joined
May 26, 2013
Posts
25,340
Location
Canberra AUSTRALIA
First Name
Peter
They are wonderful for scroll saws freeing up your two hands for control of the material, speeding up the process and allowing accurate cuts.

Peter.
 

donwatson

Fellow
Joined
May 27, 2014
Posts
2,714
Location
Glenrothes, Fife
First Name
Donald
Cowboy,
I had thoughts of fitting a foot switch to a recent machine I had but I ended up scrapping it due to a bent arm. I should have kept it and tried to fit a switch anyway as I still want to fit a switch to my present machine. A circuit diagram for your machine would help (I couldn't get one from the makers of my scrap machine), but I reckon the foot switch would need to be placed in the wire that feeds power to the motor ?
Another point is the switch should be in some sort of shoe/covered block so that it cannot be accidently trod on while changing blades etc.

Don W
 

cowboy

Registered
Joined
Feb 23, 2014
Posts
445
Location
Huddersfield
Thanks for all the advice from you guys l have got one on order only cost £5 so not a lot to waste, thanks Paul

Momentary Control Pedal Foot Switch SPDT TFS-201 250V 5-10A w 2M Cable: Amazon.co.uk: DIY & Tools
 

silver

General dogsbody
Executive Member
Joined
Jun 29, 2013
Posts
6,301
Location
Somewhere in Staffordshire,
First Name
Eamonn.
Something I never thought about..Looks like a good option, if I was using my scroll saw more I would be tempted with this mod myself..:thinks:

Cowboy,
Another point is the switch should be in some sort of shoe/covered block so that it cannot be accidently trod on while changing blades etc.

Don W

Surely it's good safety policy to remove the mains plug on "any" machine when replacing blades and not rely on the stop/start switch tho Don:rolling:
 

bigbob

Graduate Member
Joined
Oct 31, 2014
Posts
557
Location
Inverness
First Name
Bob
I bought one last year but have never got around to wiring it in. I bought one with 15-amp rating as I thought it would have bigger contacts on with a hope that it would work longer. When wiring it you are putting the neutral and earth wires straight through and taking a loop out of the live and switching it with a non-latching (momentary) switch. If it’s a modern machine by law it will have a NVR fitted you will either have to bypass this or pick up the feed from the output. It is 240 volts mains you are dealing with so with that in mind I would solder the wires on each side of the live cable that goes into the terminal so that the screws have something to bite into when screwed in I would give it a good tug test as you do not want a 240v live cable flying about the inside of the footswitch I would also use heat shrink up tight to the terminal blocks below is a rough circuit I nicked off another site.

footswitch wiring.jpg
 
Warning! This thread has not had any replies for over a year. You are welcome to post a reply here, but it might be better to start a new thread (and maybe include a link to this one if you need to).
Top