• Thanks for visiting The Penturners Forum today.

    There are many features and resources that currently you are unable to see or access, either because you're not yet registered, or if you're already registered, because you're not logged in.

    To gain full access to the forum, please log in or register now. Registration is completely free, it only takes a few seconds, and you can join our well established community of like-minded pen makers.

Morse taper chuck adaptor

Themackay

Fellow
Joined
Feb 27, 2014
Posts
2,510
Location
Aberdeen
First Name
Alan
Just wondering how many people would be intrested in a no2 morse taper to M33 X3.5 thread to use for ornamental turning as an option in the set up in the last two issues of Woodturning magazine by Chris Hart
 

silver

General dogsbody
Executive Member
Joined
Jun 29, 2013
Posts
6,301
Location
Somewhere in Staffordshire,
First Name
Eamonn.
Just wondering how many people would be intrested in a no2 morse taper to M33 X3.5 thread to use for ornamental turning as an option in the set up in the last two issues of Woodturning magazine by Chris Hart

Yes, I would be interested, but would need to ensure that the MT fitting is threaded so it can be locked in place..(tail end internally)

It would open up a few areas for me to use my chucks on other kit..:thinks:

In trust being a tight Scotsman the price will be right..:winking:
 

silver

General dogsbody
Executive Member
Joined
Jun 29, 2013
Posts
6,301
Location
Somewhere in Staffordshire,
First Name
Eamonn.
That link is to the MT 2 threaded for Myford Alan, not sure if that's what you intended..:thinks:

But that in a 33x3.5 is what I would be after yes, I was going to do one myself but the Die for the 33 put it out of reach do me.

My taper table for my myford has a part missing so I would have to buy one of those as well and that just doesn't add up for the extra flexibility I would get.

But if the price was right then I would be interested..
 

Buckeye

ペンメーカー
Executive Member
Joined
Oct 15, 2013
Posts
9,697
Location
UK
First Name
Peter
That link is to the MT 2 threaded for Myford Alan, not sure if that's what you intended..:thinks:

But that in a 33x3.5 is what I would be after yes, I was going to do one myself but the Die for the 33 put it out of reach do me.

My taper table for my myford has a part missing so I would have to buy one of those as well and that just doesn't add up for the extra flexibility I would get.

But if the price was right then I would be interested..

Can't you cut the 33x3.5 on your myford?

Peter
 

Themackay

Fellow
Joined
Feb 27, 2014
Posts
2,510
Location
Aberdeen
First Name
Alan
Hi Peter,I have not got a Myford just posted the Myford picture first one I came across,I have a small metal lathe Seig C3 not sure what threads I can cut on it ,havnt done that since I was an apprentice.It might be an option though
 

Buckeye

ペンメーカー
Executive Member
Joined
Oct 15, 2013
Posts
9,697
Location
UK
First Name
Peter
Hi Peter,I have not got a Myford just posted the Myford picture first one I came across,I have a small metal lathe Seig C3 not sure what threads I can cut on it ,havnt done that since I was an apprentice.It might be an option though

I was replying to Eamonn who has a myford.

It might be near the limit for the Sieg.

Peter
 

Themackay

Fellow
Joined
Feb 27, 2014
Posts
2,510
Location
Aberdeen
First Name
Alan
Warning! This thread has not had any replies for over a year. You are welcome to post a reply here, but it might be better to start a new thread (and maybe include a link to this one if you need to).
Top