• Thanks for visiting The Penturners Forum today.

    There are many features and resources that currently you are unable to see or access, either because you're not yet registered, or if you're already registered, because you're not logged in.

    To gain full access to the forum, please log in or register now. Registration is completely free, it only takes a few seconds, and you can join our well established community of like-minded pen makers.

Drilling advice

Antpens

Apprentice Member
Joined
Apr 21, 2018
Posts
27
Location
Uk
First Name
Ant
Hi,

My drill press has very little depth and I'm struggling to get dead centre holes when drilling both sides. Do you have any suggestions?

I saw you can drill on the lathe but not sure where to start as I don't have a chuck, what kind would I need?
 

Burt25

Full Member
Joined
Apr 29, 2016
Posts
147
Location
N Ireland
First Name
Ian
Hi,

My drill press has very little depth and I'm struggling to get dead centre holes when drilling both sides. Do you have any suggestions?

I saw you can drill on the lathe but not sure where to start as I don't have a chuck, what kind would I need?


Ant,
Dont waste your time on the drill press if you cant get all the way through in one go, I dont think you will ever get the holes to line up.

You will need a Jacobs chuck for your tailstock with suitable morse taper and a scroll chuck with jaws which will allow holding of your pen blank securely. Drill at a slow speed regularly withdrawing the drill bit to clear the flutes. I have a drill press which can go the full depth of my blanks, but I now only drill on the lathe.
 

21William

Fellow
Joined
Jan 21, 2016
Posts
1,618
Location
Dorset
First Name
William
Yes, what Ian said. What I do is turn the blank between centres until round then put it into the chuck and drill it.
 

Antpens

Apprentice Member
Joined
Apr 21, 2018
Posts
27
Location
Uk
First Name
Ant
ah I see, how many jaws would you recommend, i also can't seem to see how you attach them as they all appear to be threaded as opposed to MT
 

Bammer

Fellow
Joined
Oct 5, 2015
Posts
1,482
Location
Cambridge
First Name
Brad
You can still use the drill press, just drill as normal then raise the bed so the bit is located in the hole and drill the rest out.

Use what you got without extra expense, try it first
 

AllenN

Fellow
Joined
May 20, 2013
Posts
2,242
Location
Lancaster, UK
First Name
Allen
I managed with Axminster C jaws quite well for ages. More recently I put some Axminster pen jaws on the chuck which also work well. Not sure they are a huge improvement but they are a bit easier and more secure. If you buy a chuck C jaws are more generally useful. I don’t usually turn to round first as you can hold a square section quite securely in both types of jaw.
Morse taper Jacobs chucks are readily available. If you can find one which is drilled to take a drawbar that might be a good option because it gives you another tool in your turning armoury since it allows you to safely use the Jacobs chuck in the headstock too. I would not do that without a drawbar since there is a risk of a morse taper coming loose at a critical moment. I know a lot of people do, but I wouldn’t, I just don’t want to take the risk.
To drill a blank as has been said you have the drill bit held in the Jacobs chuck in the tailstock and rotate the blank. If the mores taper spins in may be a nuisance but nothing more.
 

xjr1300

Full Member
Joined
Feb 3, 2018
Posts
154
Location
Devon
First Name
Pat
Hi Ant, this is what I use. The pen jaws are great for drilling segmented blanks and I also use a centre drill bit to start.

Pat20180611_134948.jpg
 

Bill Mooney

Blind old git
Grand Master
Joined
Aug 16, 2014
Posts
10,997
Location
County Durham
First Name
Bill
You’ve been given some good advice there. Try Brads advice first as it won’t cost you anything but a little bit of time.
 

Penpal

Grand Master
Joined
May 26, 2013
Posts
25,340
Location
Canberra AUSTRALIA
First Name
Peter
I like the centre drill with its shoulder champher cut as well as its sturdy construction, a range of choices in sizes.

Peter.
 

21William

Fellow
Joined
Jan 21, 2016
Posts
1,618
Location
Dorset
First Name
William
I haven't seen those before, will be ordering one tonight. cheers William

Pat

The clue is in the name really. A spotting drill is for accurately spotting, or starting a hole. A centre drill is for making a recess for turning between centres, it generates clearance for the tip of the live centre.

I was turning a very small component on my metal lathe some years ago and when complete I couldn’t help notice the hole in it was not concentric. I’d used a centre drill to start the hole off and it obviously wandered. After it landed in the bin I ordered a couple of spotting drills and I’ve never had the same problem again. The replacement part was spot on! :funny:

I use a Metal Lathe and a Milling machine and use spotting drills for every job that needs a hole in it.
 
Warning! This thread has not had any replies for over a year. You are welcome to post a reply here, but it might be better to start a new thread (and maybe include a link to this one if you need to).
Top