• Thanks for visiting The Penturners Forum today.

    There are many features and resources that currently you are unable to see or access, either because you're not yet registered, or if you're already registered, because you're not logged in.

    To gain full access to the forum, please log in or register now. Registration is completely free, it only takes a few seconds, and you can join our well established community of like-minded pen makers.

What are the best drill bits for hardest steel?

Phil Dart

Moderator
Executive Member
Joined
Nov 28, 2014
Posts
5,455
Location
Colebrooke, Devon
First Name
Phil
Drill bits with added cobalt are generally used for drilling steel I think. A quick google for cobalt drill bits will bring up a good few places to buy them in your country I suspect.
 

21William

Fellow
Joined
Jan 21, 2016
Posts
1,618
Location
Dorset
First Name
William
You can get solid carbide Drill bits for drilling tough steels but they can be expensive.

I’ve used glass drills for (delicately) opening up existing holes in hard steels.
 

Dalboy

Executive Member
Joined
Mar 20, 2014
Posts
7,679
Location
Kent
First Name
Derek
As Phil stated cobalt drill bits. But all you say is hardest steel and don't mention specifically which type of steel.
 

Penpal

Grand Master
Joined
May 26, 2013
Posts
25,340
Location
Canberra AUSTRALIA
First Name
Peter
Open ended request Larson but not a big one,easily solved in California. With the detail info of your challenge Mr Google could be your best friend supported by manufacturing businesses. The drill pictured will drill through files and glass etc I used them to drill solidified rock in Macedon tooth.

Peter.
 

Attachments

  • DSCF8603.jpg
    DSCF8603.jpg
    39.1 KB · Views: 60

EStreet

Registered
Joined
Jan 12, 2015
Posts
289
Location
USA
First Name
Ed
The only good way to drill hardened steel is solid carbide bits. Carbide flute bit that’s small then ream with a solid carbide spade bit. Don’t waste your time with TiN or cobalt bits on tempered steel.
 

johnlarson

Apprentice Member
Joined
Jun 3, 2018
Posts
7
Location
Santa Clara, CA, USA
First Name
Larson
I'm trying to think out which type of bit is best for drilling thru about 1/4" of galvanized steel. I recently used a standard carbon-steel bit to drill thru the steel. While the bit was able to drill thru it once, the second time barely made it because the bit was dulled by the first hole.
 

EStreet

Registered
Joined
Jan 12, 2015
Posts
289
Location
USA
First Name
Ed
You want something harder than what you are drilling. That way it cuts the material and not dulls the bit. Bits will dull with use and heat. Heat being the #1 enemy so you need cutting fluid.

1/4 steel you should get a carbide flute bit.
 

Walter

Moderator
Fellow
Joined
Apr 22, 2013
Posts
2,697
Location
Amble on the sunny Northumberland coast.
First Name
Walter
If it is galvanised then it is likely to be mild steel and an ordinary jobber bit should go through it without a problem if you use the correct speed and pressure and some cutting fluid. As Ed said, heat is the biggest enemy.
 

EStreet

Registered
Joined
Jan 12, 2015
Posts
289
Location
USA
First Name
Ed
Galvanized means it has a layer of zinc on it. Also FYI zinc vapor WILL not can but WILL kill you.
 

johnlarson

Apprentice Member
Joined
Jun 3, 2018
Posts
7
Location
Santa Clara, CA, USA
First Name
Larson
I was drilling deep holes in soft materials, but the flutes will get packed with chaff, and it will stop cutting. I don't understand whats wrong with my tools
 

Walter

Moderator
Fellow
Joined
Apr 22, 2013
Posts
2,697
Location
Amble on the sunny Northumberland coast.
First Name
Walter
I was drilling deep holes in soft materials, but the flutes will get packed with chaff, and it will stop cutting. I don't understand whats wrong with my tools?

If the flutes are getting filled with swarf it is your technique that is at fault not the tools. You need to withdraw the bit regularly to clear the swarf.
 

Dalboy

Executive Member
Joined
Mar 20, 2014
Posts
7,679
Location
Kent
First Name
Derek
Some metals when worked will produce long pieces of swarf where as others will chip more readily. If you are getting long pieces then as Walter stated you need to take the pressure of which will break the long chips this will need to be done regularly so that the chips can clear.
 

21William

Fellow
Joined
Jan 21, 2016
Posts
1,618
Location
Dorset
First Name
William
The most common problem when drilling steel is that people run the drill bit too fast and don’t use a suitable cutting fluid.
 
Warning! This thread has not had any replies for over a year. You are welcome to post a reply here, but it might be better to start a new thread (and maybe include a link to this one if you need to).
Top