• Thanks for visiting The Penturners Forum today.

    There are many features and resources that currently you are unable to see or access, either because you're not yet registered, or if you're already registered, because you're not logged in.

    To gain full access to the forum, please log in or register now. Registration is completely free, it only takes a few seconds, and you can join our well established community of like-minded pen makers.

Gorilla glue

alpha1

Fellow
Joined
Mar 29, 2018
Posts
1,175
Location
middlesbrough
First Name
Dave
How do you guys use gorilla glue it says on the label to wet one part of whatever you are gluing because it reacts with water. How do you use it to glue your tubes in. I have lost a couple of pen blanks because the CA is not filling the ends of the tube and there is a small gap between the blank and brass tube. Probably due to drill wander. Stuff bleeds over into the void when sanding and polishing.
 

Terry Q

Fellow
Joined
Oct 8, 2014
Posts
3,847
Location
Roanoke, Illinois USA
First Name
Terry
Do not wet the wood. It actually weakens the bond. There is enough moisture in the blank to activate the glue. However when gluing acrylics I take a deep breath and exhale through the blank. Plenty of moisture. Let the glue cure over night.
 

Penpal

Grand Master
Joined
May 26, 2013
Posts
25,340
Location
Canberra AUSTRALIA
First Name
Peter
I never wet anything even wiping carefully when I insert the potato plug in one end. Never did any heavy breathing and even though there is almost no possibility of movement whilst setting I still bind the blank end for end with rubber bands.Love Gorilla Glue.

Peter.
 

flexi

Executive Member
Joined
Sep 12, 2014
Posts
6,159
Location
Maidstone
First Name
mark
I use Gorilla, and always 'huff' with acrylic blanks:funny::funny:.
I just twist when I insert the tubes and use a mastic tube nozzel to seat fully......keeps my fingers clean:thumbs::thumbs:
 

silver

General dogsbody
Executive Member
Joined
Jun 29, 2013
Posts
6,301
Location
Somewhere in Staffordshire,
First Name
Eamonn.
When I use Gorilla glue I don't wet or dampen.

Mainly use two part epoxy as had better results and les mess IMHO.

Had an allergic reaction to CA so minimise the use of it now.
 

21William

Fellow
Joined
Jan 21, 2016
Posts
1,618
Location
Dorset
First Name
William
I rarely use Gorilla glue (Polyurethane) unless there are likely to be gaps between the parts. I much prefer Araldite (Epoxy). It’s less messy and has a far longer shelf life than Gorilla glue. I had to throw my last bottle of gorilla glue away as it had set in the bottle.
 

martin.pearson

Full Member
Joined
Nov 2, 2017
Posts
223
Location
Balingry Fife
First Name
Martin
I am still quite new to pen turning so a bit of a novice but you shouldn't really have a problem with any sort of drill prblems at the ends unless you are cutting your blanks to short. What CA are you using because a thin CA won't fill the gaps but a thick CA should be enough to take up minor gaps. I also use the twist & slide up & down method as I am pushing the tube in. A thick CA has a longer working time so allows you to do that. Also a tip someone gave was to stand the blanks on end after the CA had hardened & then drip a little thin CA around the ends.
I was having some problems with the wood breaking off the ends & that was one of the suggestions. I also tried Polyurethane which works OK but I now tend to use a combination of both, Not on the same blank I might add lol
 

Lons

Fellow
Joined
Dec 17, 2013
Posts
4,753
Location
Northumberland
First Name
Bob
Interesting!

I never use CA to glue in tubes, just epoxy or polyurethane depending on the blank and with the latter I always dampen the inside of the blank immediately before inserting the tube. Use an artists brush and can honestly say that to date have never had a failure.
I don't bother with plugging the ends either these days as it's simple enough to trim out the overspill with a scalpel and fine abrasive wrapped around a dowel. Anyway I'd rather use potatoes to make chips. :banana:

Not saying right or wrong just suits me.
 

21William

Fellow
Joined
Jan 21, 2016
Posts
1,618
Location
Dorset
First Name
William
I think you can get wet Epoxy off your fingers with Acetone, but what about Polyurethane? It certainly has its uses (I’ve made my own sanding belts with it) but boy is it nasty stuff when you get it on your hands! :sob:
 

Lons

Fellow
Joined
Dec 17, 2013
Posts
4,753
Location
Northumberland
First Name
Bob
I think you can get wet Epoxy off your fingers with Acetone, but what about Polyurethane? It certainly has its uses (I’ve made my own sanding belts with it) but boy is it nasty stuff when you get it on your hands! :sob:

Just get a box of 100 disposable vinyl gloves for a couple of quid and you don't have a problem.
 

alpha1

Fellow
Joined
Mar 29, 2018
Posts
1,175
Location
middlesbrough
First Name
Dave
I tried the Gorilla glue to day I ended up with black fingers and a right clarty mess. Ruinded a couple of blanks. I will stick with my instabond thick CA in future. I did manage to turn two beutifull Zetas though. A comission they are going to Japan. Im Global I have sent four to America. Three to Holland. Oh and two down south.:banana:
 
Warning! This thread has not had any replies for over a year. You are welcome to post a reply here, but it might be better to start a new thread (and maybe include a link to this one if you need to).
Top