• Thanks for visiting The Penturners Forum today.

    There are many features and resources that currently you are unable to see or access, either because you're not yet registered, or if you're already registered, because you're not logged in.

    To gain full access to the forum, please log in or register now. Registration is completely free, it only takes a few seconds, and you can join our well established community of like-minded pen makers.

Heres a challenge

Pierre

Graduate Member
Joined
Sep 2, 2015
Posts
996
Location
Southern Central France
First Name
Pierre
Thanks Terry it sounds like a good idea but sadly ordering anything from the USA will cost the same again in postage if not more. Which is why I have to stick to Europe.

Pierre
 

Penpal

Grand Master
Joined
May 26, 2013
Posts
25,340
Location
Canberra AUSTRALIA
First Name
Peter
Look for same size cardboard tubing and use glue backed sand paper of your choice to make your own. Possible in the so called colony must be possible in such an advanced country like france.

Peter.
 

Pierre

Graduate Member
Joined
Sep 2, 2015
Posts
996
Location
Southern Central France
First Name
Pierre
Thanks for all of the suggestions, I was looking initially for something that existed, I know I can make them it is just a pain having to make a support to fit each post to an exact diameter then find an appropriate sandpaper to fix to it and this time detracts from the actual manufacture of the boxes. This especially since everything is taking twice as long now following the op.

Pierre
 

bigbob

Graduate Member
Joined
Oct 31, 2014
Posts
557
Location
Inverness
First Name
Bob
Hi Pierre,

I have the same machine which was given to me as a retirement present when I had dreams of making electric guitar bodies. I have not found any finer grits but have thought about making my own. When I was a practising radio amateur we used to use formers to make inducters (coils) for radios transmitters and atu's etc so the idea in my head is to turn 6 formers of the same dimensions of the rubber formers that are with the machine then tightly rap carboard round them tape it up so it does not unravel and the use thin CA to stifen the cardboard then use contact adhesive to stick the the finer grade sandpaper on think the cardboard would have to be helicaly wound as with the sandpaper.
 

Pierre

Graduate Member
Joined
Sep 2, 2015
Posts
996
Location
Southern Central France
First Name
Pierre
That's an interesting thought Bob, why not just make the cylinders, centre bore them to fit the machine stem,, stick velcro on and then attach abranet which can be bought in wide ribbons ( Mirka Abranet Abrasive Roll 115mm - Abrasive Rolls - Abrasives for Power Tools - Sanding & Polishing - Power Tool Accessories - Accessories | Axminster Tools & Machinery ), the diagonal aspect is only for continuity of sanding, but with the machine bobbing up and down (pardon the pun), it shouldn't make much difference to the sanding quality, and if its velcroed on then the need for the compression washer goes away. I'll have a look at it later I have just sorted out a different fine system albeit by hand.

Thanks

Pierre :thumbs:
 

Dalboy

Executive Member
Joined
Mar 20, 2014
Posts
7,679
Location
Kent
First Name
Derek
Just for the finer grits how about a plastic pipe that the spindle will fit into and tighten on to the apply valcro and use that to attach the paper to, easily removed after use. As long as not much pressure is used I would have thought that heat build-up should not be a problem. Or even metal pipe if that worried.
 

Pierre

Graduate Member
Joined
Sep 2, 2015
Posts
996
Location
Southern Central France
First Name
Pierre
I think that the main problem is that I am too lazy to make a whole bunch of cylinders of differing diameters all precise enough to go into the ventilation guide holes (24 all told) , so that I can work my way down from 80 grit to 800 grit which is my final finish before polishing. Its all easy on the outside, but the different spindle diameters are required for the inside of the bandsaw boxes and some of the diameters also create some of the curves, so consistency is needed. In my case the abranet rolls are much cheaper here than Axminster's prices and I have them easily up to 800 grit and they last a long time because they are self cleaning (the mesh that is).
 

Frederick

Registered
Joined
Apr 8, 2018
Posts
871
Location
Chatham
First Name
Frederick
Hello Pierre

Nothing left for me to add really. All has been said. I was going to suggest Velcro backed paper, but I am sure you already thought of that.

As it happens, I am also a Radio Amateur. Still have my licence, but do not do much these days.

Cheers
Frederick
 

yorkshireman

Wood Rat
Executive Member
Joined
Jan 5, 2013
Posts
5,199
Location
wrexham
First Name
Keith
I know it’s not cheap Pierre but have you looked at the Guinevere sanding system. It gives brilliant results
 

bigbob

Graduate Member
Joined
Oct 31, 2014
Posts
557
Location
Inverness
First Name
Bob
That's an interesting thought Bob, why not just make the cylinders, centre bore them to fit the machine stem,, stick velcro on and then attach abranet which can be bought in wide ribbons ( Mirka Abranet Abrasive Roll 115mm - Abrasive Rolls - Abrasives for Power Tools - Sanding & Polishing - Power Tool Accessories - Accessories | Axminster Tools & Machinery ), the diagonal aspect is only for continuity of sanding, but with the machine bobbing up and down (pardon the pun), it shouldn't make much difference to the sanding quality, and if its velcroed on then the need for the compression washer goes away. I'll have a look at it later I have just sorted out a different fine system albeit by hand.

Thanks

Pierre :thumbs:

Hi Pierre,

Your idea is much more simple than mine but I am always reminded by my better half that I overthink things:goesred:(as if?) . Frederick I am no longer active as a radio amateur but still hold the license my callsign is GM4VIK but I loved the hobby and at one point had a big antenna farm and enjoyed building ATU's and linear amps etc but since we moved closer to civilization mainly for my wife's health I no longer have the land for antennas. I do look back with joy to my time on the air and think about how we were the first of ordinary people to network across the world with all people long before the internet was ever thought of.
 
Warning! This thread has not had any replies for over a year. You are welcome to post a reply here, but it might be better to start a new thread (and maybe include a link to this one if you need to).
Top