• Thanks for visiting The Penturners Forum today.

    There are many features and resources that currently you are unable to see or access, either because you're not yet registered, or if you're already registered, because you're not logged in.

    To gain full access to the forum, please log in or register now. Registration is completely free, it only takes a few seconds, and you can join our well established community of like-minded pen makers.

Drill size

Themackay

Fellow
Joined
Feb 27, 2014
Posts
2,510
Location
Aberdeen
First Name
Alan
Those of you that make TM Omegas what size of drill do use use for the cap tube I tend to find the 15/32 is a bit of a slack fit for the tube or am I being to fussy
 

Neil

Fellow
Joined
May 21, 2013
Posts
3,132
Location
Hitchin, Hertfordshire
First Name
Neil
15/32 is the one I use and haven’t had any problems. Could be that your drill is on the large size? Could be that there is a bit of drill wobble making the hole larger or even if you were drilling a softer fast growing species the grain can take the drill bit slightly off a true course.
 

Themackay

Fellow
Joined
Feb 27, 2014
Posts
2,510
Location
Aberdeen
First Name
Alan
15/32 is the one I use and haven’t had any problems. Could be that your drill is on the large size? Could be that there is a bit of drill wobble making the hole larger or even if you were drilling a softer fast growing species the grain can take the drill bit slightly off a true course.

Aye Neil I know occasionaly I have had a bit of drill wobble and you get a slightly larger holeI have the metric equivalent as well so find same problem with both drill I use a center drill first then @6mm then 11.5 then 15/32 or 11.9 its the only pen part that I seem to find this is an issue
 

flexi

Executive Member
Joined
Sep 12, 2014
Posts
6,159
Location
Maidstone
First Name
mark
It's normally soft acrylics I have that problem with.....then I just use a size down first and check for fit:thinks::thinks:
 

pittswood

Fellow
Joined
Mar 14, 2016
Posts
1,251
Location
Rhigos, South Wales
First Name
Kelvin
Hi Alan,
make sure the drill cutting lands are of equal length. If they are unequal, you will get wobble and enlarged holes. Measure from the bottom of the drill, up to the lower land cutting edge. Repeat on the other side and ensure the centre of the drill point is in centre.
Kelvin
 

Themackay

Fellow
Joined
Feb 27, 2014
Posts
2,510
Location
Aberdeen
First Name
Alan
Hay Alan, I use metric drill bits for the Omega 11.9mm & 9.9mm

Aye John I did buy a 11.9 mm after finding the 15/32 seemed a bit oversize still feel the hole ends up a bit oversize the glue probably fill the void ok I like things to be a neater fit though thinking I might buy a 11.7 mm
 

Themackay

Fellow
Joined
Feb 27, 2014
Posts
2,510
Location
Aberdeen
First Name
Alan
It's normally soft acrylics I have that problem with.....then I just use a size down first and check for fit:thinks::thinks:

Mabye thats part of the problem I have drills in 0.1 increments up to 10mm so just use them accoringly so never have a problem under 10mm do you think I would get away with 11.7 ok
 

flexi

Executive Member
Joined
Sep 12, 2014
Posts
6,159
Location
Maidstone
First Name
mark
Mabye thats part of the problem I have drills in 0.1 increments up to 10mm so just use them accoringly so never have a problem under 10mm do you think I would get away with 11.7 ok

I only normally have this problem with the soft 'camoflauge' blanks.....I go slow and clear swarf frequently...don't let heat build up....but always they go oversized. I can drill another blank straight after and it's a perfect fit....it's just those buggers and so I tend to go under and try first!!
On the occasions it's been baggy I wrap I turn of masking tape around 2/3rds the tube and use PU glue...it's not failed yet:praying::praying:
 

Penpal

Grand Master
Joined
May 26, 2013
Posts
25,340
Location
Canberra AUSTRALIA
First Name
Peter
Every drilling has its preferences,I find comfort in mainly one brand of drills for preference.The problems come with the proliferation of pen kit makers and dealers. Which pens do I like to make,am I to go commercial.

Bottom line measure and compensate after realising timbers vary and dryness is crucial, not waiting or correcting seasoning can cause more problems.

Peter.
 

21William

Fellow
Joined
Jan 21, 2016
Posts
1,618
Location
Dorset
First Name
William
Drill bits are commonly available in .1 mm increments so why not try a 11.8mm bit first and see if the fit is better?
 

fortress

Registered
Joined
Apr 11, 2016
Posts
5,178
Location
Astley
First Name
John
Just remember Alan, if you are painting the tubes/blanks you’ll need to allow for that in selecting a drill size. :thinks::thinks:
 
Warning! This thread has not had any replies for over a year. You are welcome to post a reply here, but it might be better to start a new thread (and maybe include a link to this one if you need to).
Top