• Thanks for visiting The Penturners Forum today.

    There are many features and resources that currently you are unable to see or access, either because you're not yet registered, or if you're already registered, because you're not logged in.

    To gain full access to the forum, please log in or register now. Registration is completely free, it only takes a few seconds, and you can join our well established community of like-minded pen makers.

Drilling Pen Blanks

Jim

Grand Master
Joined
Oct 19, 2011
Posts
15,617
I find that drilling the pen blanks on my lathe i have very little issues which i got using the pillar drill. I turn most of my blanks round before i drill them. The blanks i don't turn round are made of corian. I use a colt drill and can usually do one pass through the blank running at 800rpm ...

How do you drill your blanks? ... :thinks:

lathe_drilling.jpg
 

yorkshireman

Wood Rat
Executive Member
Joined
Jan 5, 2013
Posts
5,199
Location
wrexham
First Name
Keith
I've never tried drilling on the lathe, its something I'll have a go at shortly. For me its easy to use the bench drill and a hand held vice - as long as I take it easy that is.
 

ataylor

Registered
Joined
Nov 6, 2011
Posts
1,668
Location
UK
First Name
Andy
I also use a bench drill and a trusty bench vice. This method is hit a miss, the best results are when the blank is totally square. :thumbs:
 

Mattyd

AKA 'The Dundee Redneck'
Graduate Member
Joined
Dec 21, 2012
Posts
583
Location
Dundee
as above, drill vice, and a drill stand..... Crap results.... but I dont have a lathe chuck...
 

ataylor

Registered
Joined
Nov 6, 2011
Posts
1,668
Location
UK
First Name
Andy
That's a good idea Jim, turning them round before drilling, i will start to do this as i lose quite a few blanks with the hole to near the side of the blank. I get really nervous when i have spent a few quid on a decent blank only to toss it in the bin. :rolling:
 

Jimjam66

Chief Battonager
Registered
Joined
Jan 27, 2013
Posts
3,775
Location
Basingstoke, Hampshire
I'm another who doesn't have the kit to drill on the lathe, which got me thinking about Longworth chucks. The tail stock drill chuck is pretty cheap (£11 at Axminster), but the headstock chuck is big $$$. Has anyone here built a Longworth chuck, and if so do you have any tips?

David
 

The Wood Bucket

Full Member
Joined
Mar 28, 2012
Posts
189
Location
New York USA
I'm another who doesn't have the kit to drill on the lathe, which got me thinking about Longworth chucks. The tail stock drill chuck is pretty cheap (£11 at Axminster), but the headstock chuck is big $$$. Has anyone here built a Longworth chuck, and if so do you have any tips?

David

I have not built a longworth Chuck, but a friend of mine has. That chuck would not help with the drilling of the blanks. It would not go small enough. Also the Longworth chuck is only made for taking very light cuts or sanding and is designed for only finishing off the bottom of a piece that you turned either on a faceplate or with a tenon in a 4 jaw chuck. They are great to have, but they have a purpose. Right now I use my Cole Jaws to finish bowls.
 

ataylor

Registered
Joined
Nov 6, 2011
Posts
1,668
Location
UK
First Name
Andy
I'm another who doesn't have the kit to drill on the lathe, which got me thinking about Longworth chucks. The tail stock drill chuck is pretty cheap (£11 at Axminster), but the headstock chuck is big $$$. Has anyone here built a Longworth chuck, and if so do you have any tips?

David

I Can't better the reply from Gary regarding the Longworth David, but depending on what lathe you have you could try this Click Me for drilling on the lathe. :nooidea:
 

Jimjam66

Chief Battonager
Registered
Joined
Jan 27, 2013
Posts
3,775
Location
Basingstoke, Hampshire
Thanks WB and Tony. I wondered whether the Longworth would be strong enough, seeing as its made of wood or Perspex. Of course, you're right that it might not close to a small enough diameter to grab a pen- blank either. D'oh!

Tony, thanks for the link. Fiendishly clever idea. I did something similar to create two 'pads' that fit into the head and tailstock tapers so that I can press kit parts into the pen tubes on the lathe. Might be too wasteful of precious blanks to turn a taper for jam-fitting to drill, though? Unless I'm missing your point ...:thinks:

David
 

ataylor

Registered
Joined
Nov 6, 2011
Posts
1,668
Location
UK
First Name
Andy
No i pointed you to that link of Jim's to show you that you could turn down a blank to fit into the spindle to drill the hole for the pen barrel, there is no waste mate. :thumbs:
 

Jim

Grand Master
Joined
Oct 19, 2011
Posts
15,617
To drill the hole for the handle i turned the Sassafras to a size so that it would fit into the bore of the Spindle on the head stock ...

To do this depends on the lathe you have, i actually turned this to the size of my spindle thread as it was about the same size i had in mind for the handle ... :bwink:
 

Jimjam66

Chief Battonager
Registered
Joined
Jan 27, 2013
Posts
3,775
Location
Basingstoke, Hampshire
No i pointed you to that link of Jim's to show you that you could turn down a blank to fit into the spindle to drill the hole for the pen barrel, there is no waste mate. :thumbs:

Right, think I've got you Tony. Will give it a try and report back! Will have to order a drill chuck from Axminster first, though ... What excuse for the wife THIS time? :thinks:
 

ataylor

Registered
Joined
Nov 6, 2011
Posts
1,668
Location
UK
First Name
Andy
What excuse for the wife THIS time? :thinks:

They have just come out with a new product called a chuck love, and if i get it now i can save £20 before it hits off and everyone will want one. Hope this helps mate. :ciggrin:
 

Old Corky

Full Member
Joined
Jun 19, 2013
Posts
54
Location
Pine Island,Texas, USA
I don't know if you have a Harbor Freight Tool store or the equivalent (Cheap imported tools) in England, but I purchased a 5 speed bench drill press from them a couple of years ago, priced at $69.00 and have with no problems drilling blanks. That's cheaper than a good electric hand drill and a whole lot more accurate.

Old Corky
 
Warning! This thread has not had any replies for over a year. You are welcome to post a reply here, but it might be better to start a new thread (and maybe include a link to this one if you need to).
Top