• Thanks for visiting The Penturners Forum today.

    There are many features and resources that currently you are unable to see or access, either because you're not yet registered, or if you're already registered, because you're not logged in.

    To gain full access to the forum, please log in or register now. Registration is completely free, it only takes a few seconds, and you can join our well established community of like-minded pen makers.

Sandblasting pen kits

Skin-Job

Full Member
Joined
Oct 6, 2017
Posts
172
Location
London, England
First Name
Karl
Has anyone ever tried sandblasting a commercial pen kit, to see if the finish can be matted back?

While I love kits like the Sirocco and the Zeta, I sometimes find the factory finishes a bit plasticky and toylike.

I'm going to dig out my blasting cabinet and try to flat the finish on a Zeta kit parts, I think.
I'll be interested to see if the finish holds up.....

Anyone tried it?
 

Dalboy

Executive Member
Joined
Mar 20, 2014
Posts
7,679
Location
Kent
First Name
Derek
The finish on many pens is only a plating and you will find that it will disappear very quick.
 

Skin-Job

Full Member
Joined
Oct 6, 2017
Posts
172
Location
London, England
First Name
Karl
I totally understand and fully appreciate that the kits are base metal, electroplated.

The plating may well be thick enough to take a light pass with a sandblaster. I'm talking about a fine grit at low pressure, just enough to take the shine of and leave it satin.

Wondered if anyone had tried it.
 

Skin-Job

Full Member
Joined
Oct 6, 2017
Posts
172
Location
London, England
First Name
Karl
oooh. I've seen and made the Zeta in brushed pewter. Haven't seen brushed chrome.

The problem with the 1000 or 1500 micromesh is getting into all the crannies, and getting an even finish.

Hmmm.....
 

21William

Fellow
Joined
Jan 21, 2016
Posts
1,618
Location
Dorset
First Name
William
There are a couple of kits made in the UK that are made from Stainless Steel, you could safely sandblast these.

I sandblasted a dip pen that I made from alloy and that looked nice. I used Alox.

The media used can make a big difference to the final finish though, what do you have in mind?
 

21William

Fellow
Joined
Jan 21, 2016
Posts
1,618
Location
Dorset
First Name
William
William any tips on sandblasting?:thinks:

No, not really apart from choosing the right media for the job and observing the safety precautions. I use a medium Aluminium oxide grit in my cabinet that gives a nice Matt finish. I’ve used this on quite a lot of the tools I’ve made as it looks nice and can hide light machining marks etc. This is one of the tools I blasted a while back. Once it comes out of the cabinet I wipe it down with some microcrystalline wax to stop it rusting.

E0D105C9-F4EC-4A78-922D-8E868B1EADBA.jpg

As a point of interest I have a small Clarke blasting cabinet powered by a 2.5 HP compressor with a 25L reservoir. It’s almost exactly half the recommended power but I’ve found it works fine for the relatively small stuff I do.
 

Bill Mooney

Blind old git
Grand Master
Joined
Aug 16, 2014
Posts
10,997
Location
County Durham
First Name
Bill
Try 0000wire wool it should get into all the nooks & crannies. If that doesn’t work try valve grinding paste or some similar medium & use a rotary toothbrush with an old brush on to get into the nooks etc.
 

silver

General dogsbody
Executive Member
Joined
Jun 29, 2013
Posts
6,301
Location
Somewhere in Staffordshire,
First Name
Eamonn.
Never done it or even thought about it! But Interesting on this thead to see what turns out...

No pressure Karl.. [MENTION=1739]Skin-Job[/MENTION]...
 

wm460

Grand Master
Joined
Mar 16, 2013
Posts
23,095
Location
Tennant Creek, Northern Territory, Australia.
First Name
Mark
No, not really apart from choosing the right media for the job and observing the safety precautions. I use a medium Aluminium oxide grit in my cabinet that gives a nice Matt finish. I’ve used this on quite a lot of the tools I’ve made as it looks nice and can hide light machining marks etc. This is one of the tools I blasted a while back. Once it comes out of the cabinet I wipe it down with some microcrystalline wax to stop it rusting.

View attachment 34175

As a point of interest I have a small Clarke blasting cabinet powered by a 2.5 HP compressor with a 25L reservoir. It’s almost exactly half the recommended power but I’ve found it works fine for the relatively small stuff I do.

Very nicely done William.:thumbs:

Just have a look at sand blaster supplies in Alice Springs, they have the following, what are you recommendations,

Garnet F24

Blackridge Sand Blasting Grit - Garnet - 10kg - Supercheap Auto


Silicone Carbide F30

Blackridge Sand Blasting Grit - Silicone Carbide - 10kg - Supercheap Auto

Glass Bead

Blackridge Sand Blasting Grit - Glass Beed - 10kg - Supercheap Auto

Sand Blasting Grit

Norton Air Sand Blasting Grit - 10kg - Supercheap Auto
 

Penpal

Grand Master
Joined
May 26, 2013
Posts
25,340
Location
Canberra AUSTRALIA
First Name
Peter
I bought and used a sandblasting kit years later gave it to a mate.I bought heaps of pure garnet from a pro sandblasting firm who bought it in a sling of one ton AU. I still marvel because I love Garnets.

You can buy Shakespeare Pen Kits through Phil the co producer of them in bright chrome or matte.

Peter.
 

wm460

Grand Master
Joined
Mar 16, 2013
Posts
23,095
Location
Tennant Creek, Northern Territory, Australia.
First Name
Mark
Warning! This thread has not had any replies for over a year. You are welcome to post a reply here, but it might be better to start a new thread (and maybe include a link to this one if you need to).
Top