• Thanks for visiting The Penturners Forum today.

    There are many features and resources that currently you are unable to see or access, either because you're not yet registered, or if you're already registered, because you're not logged in.

    To gain full access to the forum, please log in or register now. Registration is completely free, it only takes a few seconds, and you can join our well established community of like-minded pen makers.

Whats the best drill bits.

silver

General dogsbody
Executive Member
Joined
Jun 29, 2013
Posts
6,301
Location
Somewhere in Staffordshire,
First Name
Eamonn.
I need to replace some of my drill bits for drilling pens. What type are best.
Glen:thinks:

I tend to drill the blanks rather than the pens :tongue: [MENTION=1196]glenpen[/MENTION]

I have quite a few standard spur tipped ones that I find are brilliant. But standard drill bits apart from that, just need to be aware and drill steady through the blanks to minimise break out.

Try UK drills UK Drills - The on-line choice for Drill Bits, Jig Saw Blades, Cutting Discs and Screwdriver Bits Always found them very good.
 

21William

Fellow
Joined
Jan 21, 2016
Posts
1,618
Location
Dorset
First Name
William
Standard twist drills are the only readily available type that you can get in a full range of sizes in .1mm steps so that’s what I use. I should add that I do all my drilling on my lathe, not the drill press. You can spend money on fancy drill bits but sooner or later you’re going to need a 10.2 or a 13.3 or whatever. If you can’t drill a straight hole in wood or plastic with a standard twist drill your technique is wrong.
 

Penpal

Grand Master
Joined
May 26, 2013
Posts
25,340
Location
Canberra AUSTRALIA
First Name
Peter
William one time I did a complete audit of all my drills and I found most were under or over by those small amounts,took so long I want special sizes I caliper at the dealer and get just under and just over.

Peter.
 

AllenN

Fellow
Joined
May 20, 2013
Posts
2,242
Location
Lancaster, UK
First Name
Allen
Glen, I find that if I need to buy locally then the Dewalt are the best option. By the web one has more choice but as has been said the only ones generally available in small increments are standard drills. I have some Colt which I do use on acrylic and they cut well and also have the advantage of extra length but whether they are really worth the premium is perhaps debatable.
I too measure rather than rely on what the bit says it is especially with the standard drills and I also drill on the lathe.
For metal work I use Presto but I preserve these for that use as there I need greater accuracy. Hope this helps.
 

21William

Fellow
Joined
Jan 21, 2016
Posts
1,618
Location
Dorset
First Name
William
If you do feel you need a “special” drill bit for some reason just buy a 10mm and use this to drill the initial hole then follow it up with a twist drill of the correct size. Buying a complete set of special bits in sizes you’ll likely never use for pen making seems a waste.
 

Penpal

Grand Master
Joined
May 26, 2013
Posts
25,340
Location
Canberra AUSTRALIA
First Name
Peter
I will never forget a close friend of mine wanted a very special pen for her Solicitor Son had to be bla bla bla and stunning. This I made 100.00 then two more special orders same price but had to be faux Ivory. I had two sticks,had them for ages. Turning the cap end on a Roman Harvest iI had a chip out,just tiny but. So I got the last piece just long enough for the cap need fast running out of time used my 33/64 drill which left just enough meat to finish cut and polish later.

To my horror and disbelief my perfect hole and as I watched in horror and disbelief the piece sagged almost 30 degrees, reached out softly and brought it to the horizontal and managed to hold it still for a short time. Breathing was difficult but it worked. When glued the top and finished turning I popped the top and made a piece of Faux crap. Pic of the finished pen. To this day when I make Roman Harvest Pens I wonder at the makers of the kit with the odd sized drills needed and the ever so thin margin of material left on the cap half.
 

Attachments

  • DSCF0001.jpg
    DSCF0001.jpg
    29.5 KB · Views: 31
Warning! This thread has not had any replies for over a year. You are welcome to post a reply here, but it might be better to start a new thread (and maybe include a link to this one if you need to).
Top