• Thanks for visiting The Penturners Forum today.

    There are many features and resources that currently you are unable to see or access, either because you're not yet registered, or if you're already registered, because you're not logged in.

    To gain full access to the forum, please log in or register now. Registration is completely free, it only takes a few seconds, and you can join our well established community of like-minded pen makers.

Disasters

alpha1

Fellow
Joined
Mar 29, 2018
Posts
1,175
Location
middlesbrough
First Name
Dave
I have made quite a few pens now I was asked to make ten for the Company I work for to distribute to customers so I had time to get some practice in. I bought a couple of rollerball kits and matching fountain pen kits to make I left them in a draw until I got the ten out of the way with the intention of turning them when I had time on my hands.

I bought two wood blanks for one set and two blanks of unknown material to make up the two pen sets. The wood blanks were a disaster. The cap was OK but the body of the pen developed a split in the wood.
The second set of wood blanks a hole appeared in the nib end through to the brass and the cap chipped. So two blanks and no pen.
I moved onto the second set of blanks I don't know what they were made of but they shattered like bars of rock. One when cutting to length:thinks::sob: and the other while on the mandrel. So an expensive week end up to now.
This is a picture of one of the wood blanks. The other one developed a hole through to the brass while sanding.
 

Attachments

  • pens 007.jpg
    pens 007.jpg
    40.4 KB · Views: 88
  • pens 008.jpg
    pens 008.jpg
    34 KB · Views: 87

fortress

Registered
Joined
Apr 11, 2016
Posts
5,178
Location
Astley
First Name
John
Oh! Dave that’s so unlucky and so disappointing, but you are not alone. keep yearning keep turning.:thinks:
 

Phil Dart

Moderator
Executive Member
Joined
Nov 28, 2014
Posts
5,455
Location
Colebrooke, Devon
First Name
Phil
Beautiful wood Dave - I hope you can rescue the disasters. Have you managed to identify why the pRoblems have occurred?
 
Joined
Dec 14, 2017
Posts
1,105
Location
Lake District
First Name
Craig
A bit of bad luck. Do as Paul suggested. I had a similar problem when I used black palm. Bill Mooney, gave me a few tips and one was to use the dust and CA. It’s surprising what can be rescued. Best of luck.

Regards

Craig:thumbs:
 

Paul hd

Fellow
Joined
Jun 12, 2016
Posts
1,299
Location
Buckinghamshire
First Name
Paul
Unfortunately I have cleaned up the lathe and work area so the turnings etc have gone in the bin.:sob:

You don't need to use the dust from the original turning. You could turn another bit of wood and collect. You could run your finger along a shelf and pick up some sawdust.

I only say this because that wood looks really nice.
 

Dalboy

Executive Member
Joined
Mar 20, 2014
Posts
7,679
Location
Kent
First Name
Derek
You don't need to use the dust from the original turning. You could turn another bit of wood and collect. You could run your finger along a shelf and pick up some sawdust.

I only say this because that wood looks really nice.

Another solution for wood dust is to do as I have done. When making a project and I sand a lot of the same wood I collect this and keep it with a label in a mustard jar. I now have a collection of fine sawdust of different colours to use at a later date.
 

xjr1300

Full Member
Joined
Feb 3, 2018
Posts
154
Location
Devon
First Name
Pat
What glue do you use for the tubes? I use gorilla glue and find it holds it all together that much better.

Pat
 

Gregory Hardy

Graduate Member
Joined
Jul 7, 2017
Posts
454
Location
Upper New York State
First Name
Greg
Derek - I thought I was the only one with a case of OCD that forces me to bag and label sanding dust! (They are arranged in a drawer in alphabetical order, of course.)

I also use gorilla glue (as Pat notes above) and have had far fewer "explosions." Because it expands, any interior voids get glue coverage too.

Beautiful blanks, Dave, and the turning looks great. I hope you hung on to the ones that gave you trouble and can salvage something. I have spent many hours (collectively) on my hands and knees in the shop looking for the "shrapnel" of a burl pen blank that exploded. Reconstruct right on the lathe with CA, dust and the found pieces. Stay the course and buy some knee pads!
 

Penpal

Grand Master
Joined
May 26, 2013
Posts
25,340
Location
Canberra AUSTRALIA
First Name
Peter
I tend to dice problems. In the event I keep a container alongside the lathe and time turnings in there just in case I want to fill a minor problem. One on top of another to be sure to be sure.

Peter.
 

Bill Mooney

Blind old git
Grand Master
Joined
Aug 16, 2014
Posts
10,997
Location
County Durham
First Name
Bill
If you have an off cut of the blank sand it on your disc sander without extraction & use the dust that’s left on the sander table. Good luck.
 
Warning! This thread has not had any replies for over a year. You are welcome to post a reply here, but it might be better to start a new thread (and maybe include a link to this one if you need to).
Top