• Thanks for visiting The Penturners Forum today.

    There are many features and resources that currently you are unable to see or access, either because you're not yet registered, or if you're already registered, because you're not logged in.

    To gain full access to the forum, please log in or register now. Registration is completely free, it only takes a few seconds, and you can join our well established community of like-minded pen makers.

Right Kit

Tony

Full Member
Joined
Jan 29, 2020
Posts
78
Location
Wiltshire
First Name
Tony
Not sure whether this point/ question deserves a thread but:

My dad who was a mechanical engineer by trade always said to me, "get the best tools that you can afford". Me, as a sales person, didn't really pay it much attention. I brought a cheap tap and die set and have been 'blowing' the thread 5 in every 6 attempts to cut a thread. I have put that down to inexperience. Having finally figured out what dies I need, I brought 4 good quality ones and, yep, turns out it wasn't me so much as blunt dies.

Anyway, on the subject of right kit for the job. I have been mulling over moving from my wood lathe - Record power DML320 (which I love) to a metal lathe. I have had a good look through previous threads, and don't want to cover old ground, but am interested in what the general view is on a move to a £500 metal lathe for creating bespoke pens.

Good investment or a wood lathe can achieve all that is needed?
 

Phil Dart

Moderator
Executive Member
Joined
Nov 28, 2014
Posts
5,455
Location
Colebrooke, Devon
First Name
Phil
The major advantage of an engineering lathe over a wood lathe for your purposes, is accuracy and repeatability. You don't need the engineering lathe, but turning with hand tools on a wood lathe is far more hit and miss on a micro level than with controlled tool holders on an engineering lathe. Do-able on either, but better tolerances on the finished article with the latter.
 

Penpal

Grand Master
Joined
May 26, 2013
Posts
25,340
Location
Canberra AUSTRALIA
First Name
Peter
I have both and I believe they serve their purposes well. I also support the excellence in metal lathe accuracy from time to time and the independance it brings for bushes etc.

Peter.
 

Tony

Full Member
Joined
Jan 29, 2020
Posts
78
Location
Wiltshire
First Name
Tony
Pete, Phil, Mark, thanks for your replies, very helpful - Metal lathe it is.

(Though not sure whether distributors are making deliveries just now, things as they are) so may need to wait.
 

Tony

Full Member
Joined
Jan 29, 2020
Posts
78
Location
Wiltshire
First Name
Tony
Good point Mark, short term, so long as they deliver, failing that I'll waiting until the country gets up and running again.

It's amazing to see lathes on ebay manufactured at the start of the 20th century still in circulation. Guess they made them well then....
 

Druthman

Full Member
Joined
Oct 1, 2019
Posts
57
Location
Redruth, Cornwall
First Name
Neil
I am a model engineer and a convert to pen making so I have three lathes. A Myford 265, a Jet wood turning lathe and a Axminster pen turning lathe. What I would say is that you should go for the best metal turning lathe that your budget can stretch too and avoid the Chinese rubbish that’s cheap but really inferior. Better to go for a second hand Myford, Boxford or similar that may have a bit of wear but can easily be adjusted to turn accurately and repeatedly. Just my thoughts, good luck in your search.
 

Penpal

Grand Master
Joined
May 26, 2013
Posts
25,340
Location
Canberra AUSTRALIA
First Name
Peter
1966 Hercus serves me wonderfully,bought 2nd hand before the year 2000. I use it most days for a whole variety of needs and wishes.:thumbs:

Peter.
 

Attachments

  • Hercus and Dremel 6-27-2008 11-46-043.jpg
    Hercus and Dremel 6-27-2008 11-46-043.jpg
    103.7 KB · Views: 14
Warning! This thread has not had any replies for over a year. You are welcome to post a reply here, but it might be better to start a new thread (and maybe include a link to this one if you need to).
Top