• Thanks for visiting The Penturners Forum today.

    There are many features and resources that currently you are unable to see or access, either because you're not yet registered, or if you're already registered, because you're not logged in.

    To gain full access to the forum, please log in or register now. Registration is completely free, it only takes a few seconds, and you can join our well established community of like-minded pen makers.

Turning speed

Tony

Full Member
Joined
Jan 29, 2020
Posts
78
Location
Wiltshire
First Name
Tony
Curious to understand what speed range people here use to turn pens.

I work between 550 for roughing out a blank up to 1750 for sanding and friction polish.

Just wondering whether it would be worth changing the belt and moving to a higher speed range.
 

Bill Mooney

Blind old git
Grand Master
Joined
Aug 16, 2014
Posts
10,997
Location
County Durham
First Name
Bill
Turning 3200. Sanding about 900. melamine finish about 900. Friction polish 3200.
For acrylics I use the same speeds for turning & sanding. For polishing acrylic about 1500.
 

Phil Dart

Moderator
Executive Member
Joined
Nov 28, 2014
Posts
5,455
Location
Colebrooke, Devon
First Name
Phil
As high as you dare for turning. You need to reduce for sanding though - sanding at high speeds just burnishes the workpiece rather than abrade it, and blunts the abrasive faster. Sanding is more effective at slower speeds. I turn at about 3400, sand and finish at about 1000, and drill at about 300
 

Tony

Full Member
Joined
Jan 29, 2020
Posts
78
Location
Wiltshire
First Name
Tony
Thanks - glad I asked.

Sanding people seem to be lower speed (which may account for some recent issues encountered) - Friction polish higher speed - Drilling lower speed. Sounds as though all 3 belt positions will be needed :rolling:.
 

Seb

Apprentice Member
Joined
Mar 20, 2020
Posts
19
Location
West Yorkshire
First Name
Seb
Hi Tony

I personally do everything at the highest speed on my little lathe (2800rpm), to avoid having to constantly change the fiddly belt. As others have mentioned, its probably not ideal to be sanding at the higher speeds, but I lighten up a lot on the pressure to counter this, and see good results. I just make sure I'm pretty thorough in sanding with the grain with the lathe turned off after the usual lathe on sanding. I drill my blanks with a drill press to avoid having to remove the mandrel.

I'll likely move up to an electronically controlled speed lathe soon in order to be able to slow it down for certain stages as mentioned by others, but I just thought I'd mention how I do it. I'm very limited for time on an evening so I like to try and get everything done in a couple of hours. I have Rheumatoid Arthritis, so fiddling with belts isn't ideal for me.
 

qquake2k

Fellow
Joined
Sep 9, 2015
Posts
1,070
Location
Northern California
First Name
Jim
I do everything at about 2,000 RPM. Roughing, final turning, sanding, polishing, I rarely change the speed. For wood and acrylic. The only time I change the speed is if I'm turning something bigger, like a pen stand. Then I'll slow it a bit.
 

Dalboy

Executive Member
Joined
Mar 20, 2014
Posts
7,679
Location
Kent
First Name
Derek
I have a manual change belt lathe and am always changing the belt position after a while it becomes second nature and does not take long. For spindle work higher speeds depending on diameter, thinner pieces = faster thicker = slightly slower. Cross-grain again depends on diameter I will turn at a slower speed than I use for spindle work. Drilling smaller bits faster than bigger bits.
Sandin depending on how I am sanding by hand or a drill mounted disc slower speeds increasing to about 1250rpm if inertia sanding.
 

21William

Fellow
Joined
Jan 21, 2016
Posts
1,618
Location
Dorset
First Name
William
I’ve got a variable speed lathe so no idea of actual speed as I seldom look at the display. High for turning small stuff like pens then quite a lot slower for sanding. With wood, finish sanding is largely done by hand in the direction of the grain.
 
Warning! This thread has not had any replies for over a year. You are welcome to post a reply here, but it might be better to start a new thread (and maybe include a link to this one if you need to).
Top