• Thanks for visiting The Penturners Forum today.

    There are many features and resources that currently you are unable to see or access, either because you're not yet registered, or if you're already registered, because you're not logged in.

    To gain full access to the forum, please log in or register now. Registration is completely free, it only takes a few seconds, and you can join our well established community of like-minded pen makers.

Aarrrgggghhhhh

Garno

Fellow
Joined
May 12, 2021
Posts
1,372
Location
Dronfield
First Name
Gary
Stupid mistake made today. :vangry:

I was cutting the nub off of a bowl today, well not really a bowl it was about 3" diameter and 1/2" deep made from sepia (I think) anyway I cut into the bowl so it now has a hole in the middle of it about 1/2 inch wide. It honestly took me hours to sand the inside to a smooth finish, put on sealer followed by friction polish and it produced a really nice finish. I can only think I used the wrong taper to push the bowl up against the disc as I had to go in at an angle to cut it.
I will post some photo's of it tomorrow.
Hope to start a pen on Wednesday or Thursday so hope that goes better.

A very peeved Gary.
 

Dalboy

Executive Member
Joined
Mar 20, 2014
Posts
7,679
Location
Kent
First Name
Derek
It has happened to many touch wood not done it yet. Either use it for something else or turn the hole so as to tidy it up then turn a contrasting piece of wood and fill the hole a little turning afterwards to clean it up and hay presto a bowl with a feature:whistling::whistling::whistling:
 

Bill Mooney

Blind old git
Grand Master
Joined
Aug 16, 2014
Posts
10,997
Location
County Durham
First Name
Bill
The joys of Woodturning. You certainly aren’t alone in that one. As has been said, try & save it. It’s all part of the learning curve. Happy turning.:thumbs:
 

Garno

Fellow
Joined
May 12, 2021
Posts
1,372
Location
Dronfield
First Name
Gary
The joys of Woodturning. You certainly aren’t alone in that one. As has been said, try & save it. It’s all part of the learning curve. Happy turning.:thumbs:

I will be hoping to save it and will give it a try tomorrow. (had visitors all day). I was originally thinking of trying to do something that [MENTION=2148]Curly[/MENTION] suggested but have thought better of it and will now try and do something that [MENTION=449]Dalboy[/MENTION] suggested :wink:
 

Dalboy

Executive Member
Joined
Mar 20, 2014
Posts
7,679
Location
Kent
First Name
Derek
I will be hoping to save it and will give it a try tomorrow. (had visitors all day). I was originally thinking of trying to do something that [MENTION=2148]Curly[/MENTION] suggested but have thought better of it and will now try and do something that [MENTION=449]Dalboy[/MENTION] suggested :wink:

When you turn the hole larger in the bowl try doing a small taper and then also taper the plug this will in effect give a larger glue area. Also don't forget to leave enough on the plug to turn a tenon so that the inside can be tided up before removing the tenon

I can't do a set up at the moment as I am ripping my workshop to pieces ready for the new one
 

Curly

Graduate Member
Joined
Nov 3, 2019
Posts
421
Location
RM of Aberdeen, Saskatchewan, Canada
First Name
Peter
Some of the guys in our club make an elongated finial that the bowl fits over about a quarter of the way down and glue them together. Makes them look a little like a cross between a Christmas ornament and a hanging mushroom. It then gets put out in the garden hanging from a tree or hook under the soffit. One paints them bright colours and hangs them high in trees above hiking trails near his cabin. :whistling:

Pete
 

Garno

Fellow
Joined
May 12, 2021
Posts
1,372
Location
Dronfield
First Name
Gary
Well what can I say?

I decided to make a feature of the hole.
Went for Oak as a plug with a small taper on it so it would fill the hole flush.
Cleaned and made the hole larger.
Plugged it using CA medium glue to secure it.
Turned the inside and managed to make a 1mm gap around part of the edge.
Tried filling the hole with CA and wood shavings to colour match.
Sanded the inside to get it silky smooth.
Stared in disbelief as the plug fell out.
Turned out the light and locked the shed for the day.

So I still have the same problem except the hole is now twice as big as it was before I started.

I have taken loads of photo's with a step by step guide as to what I did but cannot find the lead to transfer them from camera to PC, ordered one from eBay so should be with me by the weekend and I will post them all here.
 

flexi

Executive Member
Joined
Sep 12, 2014
Posts
6,159
Location
Maidstone
First Name
mark
Have you tried turning it into a bangle :funny::funny:
Sorry I couldn't resist....
TBF I think we have all had days/weeks like that and NO it's not like falling of a bike, "you've just got to get back on" neither is smashing it into a wall!!..... What I tend to do is put it in a cardboard box and put it on a cupboard or under the bench and turn something else. In a couple of weeks you will probably trip over the box or it fall on your head, then it will be time to have another crack at it.... Or just bin it:whistling::whistling:
 

Dalboy

Executive Member
Joined
Mar 20, 2014
Posts
7,679
Location
Kent
First Name
Derek
Gary CA glue would not be my first choice of an adhesive for this application, I think that many seem to think it is just easy to use it instead of waiting for other types of glue to dry even hot melt is not a glue I would use for this job(It does have it's uses)

A nice fit is needed when doing the plug so that the glue does not have to fill gaps. Like many things it is a learning curve do not be put off by it pick up the next piece of wood and throw it on the lathe.
 
Warning! This thread has not had any replies for over a year. You are welcome to post a reply here, but it might be better to start a new thread (and maybe include a link to this one if you need to).
Top