• Thanks for visiting The Penturners Forum today.

    There are many features and resources that currently you are unable to see or access, either because you're not yet registered, or if you're already registered, because you're not logged in.

    To gain full access to the forum, please log in or register now. Registration is completely free, it only takes a few seconds, and you can join our well established community of like-minded pen makers.

Minimal Equipment List for turning shafts

rahil

Registered
Joined
Apr 28, 2021
Posts
1
Location
London
First Name
Rahil
Hi Everyone,

I'd like to start turning some small parts from wood; the parts are just wooden tubes similar to pen shafts. The maximum length will be 10cm and the interior diameter will always be the same.

I'm putting together a minimal tools list and I was hoping you could check & advise on anything I've missed. I live in a flat so smaller is better; and I figure the parts are small anyway so I don't need big tools.


- Lathe
Seems like Axminister is the most recommended brand, but I'm wondering if I can get away with the cheapest one? Or the Charnwood W815P which seems to be in stock.
There are also small metal lathes; I assume those work with wood too? For example; AXMINSTER MODEL ENGINEER SERIES C0. I'm not sure what the limitations and advantages are; I assume the more expensive models are more precise and have more torque? I would like to work with hard wood so if the cheap one limits that for example I would spend more. Precision is not so much of a factor; only the shaft hole diameter must be correct.

- Chisels
I think I can just get 2? A gouge and a flat one?

- Drill
This is another question; from my GCSE DT days I remember there was a drill part that can go on the right side of the lathe and I could drill that way... is that feasible with one of these mini lathes?
I think I need just one diameter.

- Sandpaper / Laquer
Various Grits

Apologies if these are really silly questions; I searched quite a bit but there's no real list I can find that shows the smallest number of tools you need to get started.

Cheers,
Rahil
 

flexi

Executive Member
Joined
Sep 12, 2014
Posts
6,159
Location
Maidstone
First Name
mark
Hi,..... Yes it can be done on a budget, with minimal tools.
The main difference between a metal lathe and a wood lathe is the tool post.... Metal lathes have fixed multi axis cutter heads, wood lathes just a tool rest, if you are just turning straight tubes with no shape then yes you could do this very well and quickly on a metal lathe but as you have noticed you'll be paying more for bits you don't really need.
Personally I think a good wood lathe will suffice. Axminster used to rate there tools, hobby (a couple of hours a week) Trade( maybe one day a week) Professional ( almost constant use) you may need to consider this in your choices too... Also Axminster sell off their returns at discount so their can be the odd bargain to be had.
Again Yes you can drill on the lathe with a drill chuck in your tail stock, a cheeper and less spacious option to a pillar drill, but again more load on your one machine.
Good luck, I hope this helps:thumbs::thumbs:
 

flexi

Executive Member
Joined
Sep 12, 2014
Posts
6,159
Location
Maidstone
First Name
mark
Damn.... Like yourself I also forgot...
Work holding..... You will need some form of holding device. This could be a 3 / 4 jaw chuck or centers, a live center and dead center..... Probably if your going to drill on the lathe too it will have to be a chuck of some sort.
A saw for cutting stock to length would also be a good call:thinks::thinks:
 

Geoff Kent

Graduate Member
Joined
Feb 15, 2021
Posts
496
Location
Westcliff on Sea,Essex.
First Name
GEOFF
Hi Rahil,another woodturning lathe to consider is the Record Power DML250 mini lathe rrp £259.It is their smallest lathe and would probably suit your needs perfectly.Record also do a full range of accessories eg chuck,jaws etc.They are a long established company with an excellent reputation.I am on my second Record lathe and have never had any trouble.(touchwood!)They have stockists countrywide,I guess the nearest to you would be D&M Tools Twickenham.They have a good display of Record products and their staff are always very helpful and will point you in the right direction.Hope this helps,look forward to getting hooked on turning!
Geoff.
 

alan morrison

Fellow
Joined
Feb 26, 2019
Posts
2,378
Location
Co. Down N Ireland
First Name
Alan
Welcome to the forum, Rahil.
A couple of comments.....
If you are checking out lathes my advice would be to look at the variable speed ones, much better than belt changing.
I switched from using sandpaper to Abranet sheets and havent used sandpaper on anything on the lathe since.
Like Mark above I do my drilling on the lathe also.
Alan
 

21William

Fellow
Joined
Jan 21, 2016
Posts
1,618
Location
Dorset
First Name
William
For Precision work on small parts I use an ER32 collet Chuck to hold the work. If the timber is not round, which is very often the case, I turn it between centres first to fit one of my collets. I have collet chucks for both my MW and wood lathe. If turning small cylinders it’s very much easier done on the metalwork lathe.
 

alpha1

Fellow
Joined
Mar 29, 2018
Posts
1,175
Location
middlesbrough
First Name
Dave
Hi
I do most of my turning on a metal work lathe. For straight tubes its a doddle. I drill using the tail stock with the tube held in the chuck. All metal lathes come with a chuck as standard. But if you find you want to branch out later on into wood turning you may find the metal lathe unsuitable. I have both. A metal working lathe and a Axminster variable speed wood lathe.
 
Warning! This thread has not had any replies for over a year. You are welcome to post a reply here, but it might be better to start a new thread (and maybe include a link to this one if you need to).
Top