• Thanks for visiting The Penturners Forum today.

    There are many features and resources that currently you are unable to see or access, either because you're not yet registered, or if you're already registered, because you're not logged in.

    To gain full access to the forum, please log in or register now. Registration is completely free, it only takes a few seconds, and you can join our well established community of like-minded pen makers.

Right Pig of a Day

Garno

Fellow
Joined
May 12, 2021
Posts
1,372
Location
Dronfield
First Name
Gary
Had better days before now.

First off I had a beautiful blank of Black Palmira that decided to break in half (Lengthways) just as the drill bit was exiting, (Split with drill inside if you get my meaning).
Oh well all is not lost as I had a lovely bit of Wenge that I could use.
Cut blank to size and drilled a lopsided hole, it is too far over on one side to risk turning.
Drilled a hole into another bit of Wenge.
Prepared tube and covered with CA.
Went to put tube into sleeve and my hand twitched, tube flew into the air and landed on the only part of the floor that had sawdust, got covered in it and unable to use.
Prepared second tube, just about to put in tube and hand twitched a second time, tube landed in the exact same place as the first one.
Prepared third tube, both hands got covered in CA but at least the tube is now inside the hole I drilled for it.
 

waterbuffalo

Full Member
Joined
Sep 15, 2021
Posts
335
Location
Plymouth
First Name
nigel
Had better days before now.

First off I had a beautiful blank of Black Palmira that decided to break in half (Lengthways) just as the drill bit was exiting, (Split with drill inside if you get my meaning).
Oh well all is not lost as I had a lovely bit of Wenge that I could use.
Cut blank to size and drilled a lopsided hole, it is too far over on one side to risk turning.
Drilled a hole into another bit of Wenge.
Prepared tube and covered with CA.
Went to put tube into sleeve and my hand twitched, tube flew into the air and landed on the only part of the floor that had sawdust, got covered in it and unable to use.
Prepared second tube, just about to put in tube and hand twitched a second time, tube landed in the exact same place as the first one.
Prepared third tube, both hands got covered in CA but at least the tube is now inside the hole I drilled for it.

i was meant to be changing a kitchen sink base unit at work...ended up ripping out the entire kitchen, plus the floor and the sub floor bearers and insulation...oh, and all the wall tiles too :sob:
 

alan morrison

Fellow
Joined
Feb 26, 2019
Posts
2,420
Location
Co. Down N Ireland
First Name
Alan
Had better days before now.

First off I had a beautiful blank of Black Palmira that decided to break in half (Lengthways) just as the drill bit was exiting, (Split with drill inside if you get my meaning).
Oh well all is not lost as I had a lovely bit of Wenge that I could use.
Cut blank to size and drilled a lopsided hole, it is too far over on one side to risk turning.
Drilled a hole into another bit of Wenge.
Prepared tube and covered with CA.
Went to put tube into sleeve and my hand twitched, tube flew into the air and landed on the only part of the floor that had sawdust, got covered in it and unable to use.
Prepared second tube, just about to put in tube and hand twitched a second time, tube landed in the exact same place as the first one.
Prepared third tube, both hands got covered in CA but at least the tube is now inside the hole I drilled for it.

Gary, put the tubes on your mandrel and very lightly turn the gunk off them.
 

21William

Fellow
Joined
Jan 21, 2016
Posts
1,619
Location
Dorset
First Name
William
From what I’ve heard about it, they should pay customers to take Black Palmira away! :funny:
 
Warning! This thread has not had any replies for over a year. You are welcome to post a reply here, but it might be better to start a new thread (and maybe include a link to this one if you need to).
Top